1.5A H-bridge Dual Channel DC Motor Driver Module L298N PWM Speed Control
Overview:
Motor drive module is ideal for use in battery-powered smart car, toy cars, robots.
Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors, can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed.
Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored.
Features:
Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered.
L298N internal transistor switch, low efficiency, high fever, need to add heat sink, bulky, L298N very easy to burn
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped.
Small size, light weight, 0 standby current, is the ideal choice for your car model.
Precautions:
1. Power positive and negative reversed will certainly cause damage to the circuit.
2. Output is shorted to ground or output short circuit, and the motor stall, the chip will heat protection, but in the near or exceeding 10V voltage and peak current is greater than 2.5A situation can also cause chip burned.
-25%
0%
L298P motor drive board for Arduino Price in Pakistan electronicstore.pk
Original price was: ₨ 3000.₨ 2500Current price is: ₨ 2500.
ZK 5AD Dual H Bridge Channel DC Motor Drive Controller Board Module Motor Commutation PWM Speed Regulator in Pakistan
Original price was: ₨ 550.₨ 450Current price is: ₨ 450.
1.5A H-bridge Dual Channel DC Motor Driver Module L298N PWM Speed Control Price in Pakistan
Original price was: ₨ 200.₨ 150Current price is: ₨ 150.
Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor.
The module supply voltage 2V-10V.
Signal input voltage 1.8-7V.
Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA).
Built-in common conduction circuit, when the input pin is left floating, the motor does not malfunction.
Built-in thermal protection circuit with hysteresis effects (TSD), without worrying about motor stall.
Product Size: 24.7 * 21 * 5mm (length, width, height), ultra-small size.
The mounting hole diameter: 2 mm
Description
Reviews (0)
Shipping & Delivery
Related products
Arduino Mega 2560 R3 In Pakistan
PERATING VOLTAGE: 5V
INPUT VOLTAGE (RECOMMENDED): 7-12V
INPUT VOLTAGE (LIMIT): 6-20V
DIGITAL I/O PINS: 54 (of which 15 provide PWM output)
ANALOG INPUT PINS: 16DC
CURRENT PER I/O PIN20 mADC CURRENT FOR 3.3V PIN: 50 mA
FLASH MEMORY: 256 KB of which 8 KB used by bootloader
SRAM: 8KB
EEPROM: 4 KB
CLOCK SPEED16 MHz
LED_BUILTIN13
LENGTH: 101.52 mm
WIDTH: 53.3 mm
WEIGHT: 37 g
Click Here to Download Open Source Arduino Software
EAGLE FILES IN .ZIP
SCHEMATICS
BOARD SIZE .IN
Ch340 Arduino Mega 2560 With Cable In Pakistan
The Mega 2560 is a micro-controller board base on the CH340. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the micro-controller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get start. The Mega is compatible with most shields design for the Duemilanove or Diecimila.
The Mega 2560 is an update to the Mega, which it replaces. The Mega2560 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the CH340 programmed as a USB-to-serial converter.
Revision 2 of the Mega2560 board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.
Ch340g Usb To Ttl(serial) Converter For Arduino Price in Pakistan
This is PL2303 CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi USB to TTL / USB-TTL /STC microcontroller programmer / PL2303 in nine upgrades plate with a transparent cover Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc. This USB-TTL converter is based on CH340G USB to Serial TTL converter chip. The module can be used for 3.3V logic level signals, and has the option to switch from 5V to 3.3V logic level using a 2 pin shunt (shortening jumper for specific pins) supplied with the module.
Esp32-cam Wifi + Bluetooth Camera Module Development Board Esp32 With Camera Module Ov2640 in Pakistan
SP32-CAM is a WIFI+ Bluetooth dual-mode development board that uses PCB on-board antennas and cores based on ESP32 chips. It can work independently as a minimum system.ESP integrates WiFi, traditional Bluetooth, and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc. Fully compliant with WiFi 802.11b/g/n/e/i and Bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other hosts MCUs to add networking capabilities to existing devices.ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals, and other IoT applications. It is an ideal solution for IoT applications.
Features:
Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
Low-power dual-core 32-bit CPU for application processors
Up to 240MHz, up to 600 DMIPS
Built-in 520 KB SRAM, external 4M PSRAM
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
Support OV2640 and OV7670 cameras with built-in flash
Support for images WiFI upload
Support TF card
Support multiple sleep modes
Embedded Lwip and FreeRTOS
Support STA/AP/STA+AP working mode
Support Smart Config/AirKiss One-click distribution network
Support for serial local upgrade and remote firmware upgrade (FOTA)
Support secondary development
GY-271 HMC5883L Triple Axis Compass Magnetometer Sensor Module in Pakistan
The GY-271 module is based on the Honeywell HMC5883L IC for low-field magnetic sensing with a digital interface for applications such as lowcost compassing and magnetometry. The HMC5883L includes state-of-theart, high-resolution HMC118X series magneto-resistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation and a 12-bit ADC that enables.
MAX6675 Module With K Type Thermocouple Price in Pakistan
This temperature sensor and module makes use of the Maxim MAX6675 K-Thermocouple to digital converter IC to provide a microcontroller compatible digital serial interface (SPI compatible) to provide accurate temperature compensated measurement of the supplied K-Type thermocouple sensor. This sensor is available at electronicstore.pk shop online in Pakistan.
USB to RS485 / USB 2.0 to RS 485 Serial Converter Adapter Price in Pakistan
The USB to RS485 Converter Adapter module support WIN7 XP Vista Linux Mac OS provides an easy-to-use RS485 interface by means of a Virtual Com Port on the user’s system. There are no command structures, whatever is sent to the Virtual Comm Port is automatically converted to RS485 and vice versa. The module is completely self-powered from the USB bus. Controlling / Communicating with RS-485 devices from your PC has never been easier! This device is plug-and-play. It shows up as a serial/com port and is accessible from applications or hyper-terminal.
Reviews
There are no reviews yet.