Technical parameters of Relay electromagnetic JZX-140FF, coil 12VDC, 250VAC/5A, DPDT-2NO + 2NC
Coil voltage:
12 [VDC]
Contacts maximum current:
5 [A]
Socket rated voltage:
250 [VAC]
Contacts configuration:
DPDT
Sockets:
2NO+2NC
Number of leads:
8 [leads]
Mounting:
THT
Operating temperature:
-40~70 [°C]
Model:
JZX-140FF
Dimensions:
28x26x13 [mm]
Relay type:
electromagnetic
Coil resistance:
270 [ohm]
“Arduino 4 Channel Relay Module Board” has been added to your cart. View cart
-19%

AZ0963-1AB-12DE 12V 5PIN RELAY
₨ 750 Original price was: ₨ 750.₨ 650Current price is: ₨ 650.

G6K-2F-Y-12VDC Signal Relay 8PIN SMD
₨ 650 Original price was: ₨ 650.₨ 575Current price is: ₨ 575.
JZX-140FF 12V 6PIN RELAY
₨ 400 Original price was: ₨ 400.₨ 325Current price is: ₨ 325.
Category: Relay/RelayModule
Description
Reviews (0)
Be the first to review “JZX-140FF 12V 6PIN RELAY” Cancel reply
Shipping & Delivery


MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
1 Channel Relay Module For Arduino
Features of 1 Channel 5 Volts Arduino Relay Module:
With isolation groove in the control area and load area.
With power and relay action indication, bright when connect and go off when disconnects.
When there is a signal in signal input, public side and the common side will break over.
It can be not only used as a microcontroller development board module but also as a home appliance control.
It can not only control the DC or AC signal but the 220V AC load.
With a permanent open and close vents contact.
It is convenient to connect with blue KF301 terminal access control cable.
Specification of Single One Channel 5V Best Arduino Relay Module:
VCC: Power interface,5V
GND: Ground
IN: Control interface.
Drive Current: At least 4mA
COM: Control circuit ground, connect to GND
Size: approx. 41 x 16 x 16mm/ 1.61 x 0.62 x 0.62''
Weight: Approx. 12g
Package Includes:
1 x 1 Channel 5V Arduino Relay Module
Best Online Shopping website for 1 Channel 5V Arduino Relay Module Single One Channel 5 Volts Relay Module For Arduino in cheap price in Karachi, Lahore, Islamabad, Rawalpindi, Sukkur, Peshawar, Multan, Quetta, Faisalabad and all over Pakistan.
1 Channel Solid State Relay Module SSR Module For Arduino
Description Additional information Reviews (0)
Description
This 5V 1 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. .This is a 1 Channel SSR Solid State Relay module which has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed)
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applly to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
Input parts :
DC+: connect power positive
DC-: connect power negative
CH1: relay module signal trigger point (Effective low-level trigger)
Features :
Has been assembl, and the electrical test pass.
It can be control directly by Microcontroller
Input control signal voltage:
0-2.5V status low level, relay OFF
3-5V status high level, relay ON
Arduino 4 Channel Relay Module Board
This is a 5V 4-channel relay interface board, and each channel needs a 15-20mA driver current. This 4-way relay module can be used to control various appliances and equipment with large current. This four-channel relay module is equipped with high-current relays that work under AC250V 10A or DC30V 10A. 5 volts relay driver module has a standard interface that can be controlled directly by the microcontroller. This relay module board allows a wide range of microcontrollers such as Arduino, AVR, PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs.
NAIS DS4E-S-5VDC DS-RELAYS
RALD5W-K 5VDC 2A 10Pins Relay
Relay 12V 5Pin
Model Number: SRD-12VDC-SL-C
Coil Power : 12V DC
Pin Out: 5 Pin – Coil – COM – NC – NO
Nominal Coil Power: 0.36w, 0.45W
Contact Capacity: 10A 250VAC/10A 125VAC 10A 30VDC/10A 28VDC
Insulation Resistance: 100M.500VDC
Operate Time: 15ms/10ms
Terminal Type: PCB
Contact Load: High Power
Product name:: 12V DC Electrical Relay SRD-05VDC-SL-C
Contact Ratings: 1A,1C
Contact Resistance: 100m (at 10A 5VDC)
Contact Material: Silver Alloy
Size: Miniature
Protect Feature: Sealed
Reviews
There are no reviews yet.