HD1-M-DC12V AG4013 MATSUSHITA RELAY 12Vdc, 1A 6PIN Relay
-21%
JQX-115F-2ZS4 5VDC 8Pin 8A 250VAC
Original price was: ₨ 450.₨ 400Current price is: ₨ 400.
B4GA003Z 3VDC Relay DPDT Fujitsu 10.6x5.7mm SMD SOP-8
Original price was: ₨ 350.₨ 275Current price is: ₨ 275.
HD1-M-DC12V AG4013 MATSUSHITA RELAY 12Vdc, 1A 6PIN Relay
Original price was: ₨ 350.₨ 275Current price is: ₨ 275.
Description
Reviews (0)
Shipping & Delivery
Related products
1 Channel Relay Module For Arduino Price in Pakistan
Features of 1 Channel 5 Volts Arduino Relay Module:
With isolation groove in the control area and load area.
With power and relay action indication, bright when connect and go off when disconnects.
When there is a signal in signal input, public side and the common side will break over.
It can be not only used as a microcontroller development board module but also as a home appliance control.
It can not only control the DC or AC signal but the 220V AC load.
With a permanent open and close vents contact.
It is convenient to connect with blue KF301 terminal access control cable.
Specification of Single One Channel 5V Best Arduino Relay Module:
VCC: Power interface,5V
GND: Ground
IN: Control interface.
Drive Current: At least 4mA
COM: Control circuit ground, connect to GND
Size: approx. 41 x 16 x 16mm/ 1.61 x 0.62 x 0.62''
Weight: Approx. 12g
Package Includes:
1 x 1 Channel 5V Arduino Relay Module
Best Online Shopping website for 1 Channel 5V Arduino Relay Module Single One Channel 5 Volts Relay Module For Arduino in cheap price in Karachi, Lahore, Islamabad, Rawalpindi, Sukkur, Peshawar, Multan, Quetta, Faisalabad and all over Pakistan.
1 Channel Solid State Relay Module SSR Module For Arduino
Description Additional information Reviews (0)
Description
This 5V 1 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. .This is a 1 Channel SSR Solid State Relay module which has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed)
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applly to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
Input parts :
DC+: connect power positive
DC-: connect power negative
CH1: relay module signal trigger point (Effective low-level trigger)
Features :
Has been assembl, and the electrical test pass.
It can be control directly by Microcontroller
Input control signal voltage:
0-2.5V status low level, relay OFF
3-5V status high level, relay ON
16 Channel Relay Module Interface Board For Arduino Price in Pakistan
Specifications Of 16 Channel Relay Board:
Operating Voltage Range: 5-12V
Maximum Voltage(V) : 250V AC
Maximum Current(A) : 10
Supply Current (A) : 10mA
Operating Temperature (°C) : -40 to 85
Opt. Relative Humidity(RH) : 20{7e82c6d62784066d1b113f595afb6e15f0ca3fec289cddd29e600df910d44428} ～ 85{7e82c6d62784066d1b113f595afb6e15f0ca3fec289cddd29e600df910d44428}
Module Interface:
1. DC+: DC power supply positive pole
2. DC-: DC power supply negative pole
3. CH1~CH16: relay signal triggering pin
Relay Output:
1. Normally closed pin (NC1~NC16): relay normally closed pin
2. Common pin (COM1~COM16): relay common pin
3. Normally opened pin (NO1~NO16): relay normally opened pin
Package Includes:
1x Opto-isolated 16 Channel 5V Relay Module (Tested and QC-OK)
Related Products:
5V 8 Channel Relay Module Board for Arduino
5V 1 CHANNEL RELAY MODULE FOR ARDUINO
6-30V 1 Channel Relay Module Switch Trigger Time Delay Circuit Timer Cycle Adjustable
How to control 16 Channel Relay module using Arduino control:
Reviews
There are no reviews yet.