Signal Frequency output range: 0-40MHz
* 4 Signal outputs: 2 sine wave outputs and 2 square wave outputs
* DAC SFDR > 50 dB @ 40 MHz AOUT
* 32-Bit Frequency Tuning Word
* Simplified Control Interface: Parallel Byte or Serial Loading Format
* Phase Modulation Capability
* +3.3 V or +5 V Single Supply Operation
* Low Power: 380 mW @ 125 MHz (+5 V)
* Low Power: 155 mW @ 110 MHz (+3.3 V)
* Power-Down Function
Like our page
-11%
HX711 Pressure Sensor Load Cell Amplifier Module Price in Pakistan
Original price was: ₨ 180.₨ 150Current price is: ₨ 150.
26 Pin GPIO Extension board for Raspberry pi Price in Pakistan
Original price was: ₨ 1000.₨ 850Current price is: ₨ 850.
DDS Signal Generator Module (0-40MHz) – AD9850 Price in Pakistan
Original price was: ₨ 4500.₨ 4000Current price is: ₨ 4000.
AD9850: 0-40MHz.
2). 2 sine wave and 2 square wave output.
3). After the 20-30MHz frequency harmonics increases, the waveform will be less and less clean.
4). Square Wave: 0-1MHz.
5). Low-pass filter with 70MHz, so the waveform better than SN.
6). Parallel and serial data input can be selected via a jumper.
7). DA produced the benchmark pin (PIN12) leads for easy adjustment to do the magnitude of the output waveform Application.
8). Comparator reference input voltage generated by the variable resistor, the resistor can be adjusted duty cycle square wave of different.
9). Active AD9850 125MHz crystal oscillator modules.
Description
Reviews (0)
Shipping & Delivery
Related products
Arduino Leonardo Atmega32u Price In Pakistan
It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs); a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.
Ch340 Arduino Mega 2560 With Cable In Pakistan
The Mega 2560 is a micro-controller board base on the CH340. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the micro-controller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get start. The Mega is compatible with most shields design for the Duemilanove or Diecimila.
The Mega 2560 is an update to the Mega, which it replaces. The Mega2560 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the CH340 programmed as a USB-to-serial converter.
Revision 2 of the Mega2560 board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.
GY-271 HMC5883L Triple Axis Compass Magnetometer Sensor Module in Pakistan
The GY-271 module is based on the Honeywell HMC5883L IC for low-field magnetic sensing with a digital interface for applications such as lowcost compassing and magnetometry. The HMC5883L includes state-of-theart, high-resolution HMC118X series magneto-resistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation and a 12-bit ADC that enables.
MQ-4 Methane Natural Gas Sensor Module For Arduino in Pakistan
MQ4 High Sensitivity Gas Methane (CNG) Detector Sensor Module is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy to use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas.
Mq3 Alcohol Sensor Detector Gas Sensor Module In Pakistan
MQ3 MQ 3 MQ-3 Alcohol Detector Gas Sensor Module is a simple to use MQ-3 Alcohol Detector Gas Sensor Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gas in the air and an easy to use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas. Perfect sensing alcohol concentration on your breath just likes common breathalyzer.
mq3 alcohol sensor working
Reviews
There are no reviews yet.