-17%
360 product view
    Click to enlarge
    Motor Driver Module L298n For Arduino Dual h Bridge Motor Driver Original price was: ₨ 450.Current price is: ₨ 350.
    Back to products
    1.5A H-bridge Dual Channel DC Motor Driver Module L298N PWM Speed Control Original price was: ₨ 200.Current price is: ₨ 150.

    L298P motor drive board for Arduino

    Original price was: ₨ 3000.Current price is: ₨ 2500.

    PACKAGE INCLUDES:
    L298P Motor Driver Shield
    KEY FEATURES OF L298P MOTOR DRIVER SHIELD:
    Drive 2 DC motors at 4.8-24V at up to 2A peak (2.5A peak) current.
    Built-in Schottky diodes to protect against motor back EMF.
    Drive 1 servo motor with a dedicated 5V regulated power.
    Built-in buzzer.
    Remote reset switch.
    Bluetooth connector (x2).
    Ultrasonic Range Finder Ping connector.
    RGB LED connector
    6 Analog/digital pins brought out to 3-pin headers with 5V and Gnd available for each input for easy sensor hookup.
    Stacking female connectors for supporting another daughter card.
    Can optionally power attached Arduino off the shield

    Compare
    Add to wishlist
    Category:
    Description

    Description
    The FunduMoto L298P Motor Driver Shield is a multi-featured motor shield based around the L298P driver chip and fits Arduino Uno or other Arduino with compatible I/O pins.

    PACKAGE INCLUDES:
    L298P Motor Driver Shield
    KEY FEATURES OF L298P MOTOR DRIVER SHIELD:
    Drive 2 DC motors at 4.8-24V at up to 2A peak (2.5A peak) current.
    Built-in Schottky diodes to protect against motor back EMF.
    Drive 1 servo motor with a dedicated 5V regulated power.
    Built-in buzzer.
    Remote reset switch.
    Bluetooth connector (x2).
    Ultrasonic Range Finder Ping connector.
    RGB LED connector
    6 Analog/digital pins brought out to 3-pin headers with 5V and Gnd available for each input for easy sensor hookup.
    Stacking female connectors for supporting another daughter card.
    Can optionally power attached Arduino off the shield.
    Logic Power subsystem
    The Arduino 5V is brought up to the shield and is available on the 6 sets of red sensor 5V pins, the yellow Ping connector for Ultrasonic Rangefinders and the 2 blue digital connectors. It is also used to power the logic portion of the L298P chip. This ensures that they have good clean 5V power independent of what the motors are doing.

    Reviews (0)

    Reviews

    There are no reviews yet.

    Be the first to review “L298P motor drive board for Arduino”

    Your email address will not be published. Required fields are marked *

    Shipping & Delivery
    wd-ship-1
    wd-ship-2

    MAECENAS IACULIS

    Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

    ADIPISCING CONVALLIS BULUM

    • Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
    • Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
    • Diam parturient dictumst parturient scelerisque nibh lectus.

    Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

    Related products

    -24%
    Compare

    Arduino Due Price in Pakistan

    ,
    Original price was: ₨ 8500.Current price is: ₨ 6500.
    This Arduino Due microcontroller is based on the board of Atmel SAM3X8E ARM CortexM3 CPU. This Arduino due board is based on 32 bit ARM core microcontroller. Atmel SAM3X8E Arduino board contains 54 digital input/ output pins, 12 analog inputs, 4 UARTs, an 84 Mhz clock, an USB OTG capable connection, 2 DAC and DAC stands for Digital to Analog Converter, 2 TWI, a power jack, an SPI header, a JTAG header, a reset button and an erase button. Arduino board contains everything needed to support the microcontroller. We just need to connect the micro USB of Arduino Due to the computer. And this cable is included in the product pack. We just need to power it with an AC to DC adapter or battery to get started. This Arduino Due is compatible with all Arduino shields. And that works at 3.3V. these are compliant with 1.0 Arduino pinout. we provide high 6 inches micro USB cable with high-quality connection Arduino Due
    Add to wishlist
    Add to cart
    Quick view
    -14%
    Compare

    Arduino Leonardo In Pakistan Atmega32u Based Development Board

    ,
    Original price was: ₨ 1850.Current price is: ₨ 1600.
    The Arduino Leonardo is a micro-controller board base on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which
    Add to wishlist
    Add to cart
    Quick view
    -14%
    Compare

    Ch340 Arduino Mega 2560 With Cable In Pakistan

    ,
    Original price was: ₨ 4000.Current price is: ₨ 3450.
    The Mega 2560 is a micro-controller board base on the CH340. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything need to support the micro-controller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get start. The Mega is compatible with most shields design for the Duemilanove or Diecimila. The Mega 2560 is an update to the Mega, which it replaces. The Mega2560 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the CH340 programmed as a USB-to-serial converter. Revision 2 of the Mega2560 board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.
    Add to wishlist
    Add to cart
    Quick view
    -18%
    Compare

    ESP32-CAM-MB Programming Adapter Board CH340 Serial To USB for ESP32-CAM Module

    ,
    Original price was: ₨ 550.Current price is: ₨ 450.
    ESP32-CAM-MB Programming Adapter Board CH340 Serial To USB for ESP32-CAM Module ESP32-CAM-MB Programming Adapter Board WIFI+Bluetooth compatible TTL Downloader Module 4.7V-5.3V for ESP32-CAM Module Shield
    Add to wishlist
    Add to cart
    Quick view
    -13%
    Compare

    Mq4 High Sensitivity Gas Methane (cng) Detector Sensor Module

    Original price was: ₨ 400.Current price is: ₨ 350.
    MQ4 High Sensitivity Gas Methane (CNG) Detector Sensor Module is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins. It provides an analog output corresponding to the concentration of the gases in the air and an easy to use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas.
    Add to wishlist
    Add to cart
    Quick view
    -13%
    Compare

    Mq9 Carbon Monoxide Methane And Lpg Gas Sensor Module In Pakistan

    Original price was: ₨ 400.Current price is: ₨ 350.
    MQ-9 Carbon Monoxide, Methane and LPG Gas Sensor Module can be use to sense Carbon Monoxide and Metahane Gas. Sensitive material of MQ-9 gas sensor is SnO2, which with lower conductivity in clean air. It make detection by method of cycle high and low temperature, and detect CO when low temperature (heated by 1.5V). The sensor’s conductivity is more higher along with the gas concentration rising. When high temperature (heated by 5.0V), it detects Methane, Propane etc. combustible gas and cleans the other gases adsorbed under low temperature.
    Add to wishlist
    Add to cart
    Quick view
    -9%
    Compare

    sp32-cam Wifi + Bluetooth Camera Module Development Board Esp32 With Camera Module Ov2640 For Arduino

    ,
    Original price was: ₨ 1680.Current price is: ₨ 1530.
    SP32-CAM is a WIFI+ Bluetooth dual-mode development board that uses PCB on-board antennas and cores based on ESP32 chips. It can work independently as a minimum system.ESP integrates WiFi, traditional Bluetooth, and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc. Fully compliant with WiFi 802.11b/g/n/e/i and Bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other hosts MCUs to add networking capabilities to existing devices.ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals, and other IoT applications. It is an ideal solution for IoT applications. Features: Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module Low-power dual-core 32-bit CPU for application processors Up to 240MHz, up to 600 DMIPS Built-in 520 KB SRAM, external 4M PSRAM Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC Support OV2640 and OV7670 cameras with built-in flash Support for images WiFI upload Support TF card Support multiple sleep modes Embedded Lwip and FreeRTOS Support STA/AP/STA+AP working mode Support Smart Config/AirKiss One-click distribution network Support for serial local upgrade and remote firmware upgrade (FOTA) Support secondary development
    Add to wishlist
    Add to cart
    Quick view
    -10%
    Compare

    USB to RS485 / USB 2.0 to RS 485 Serial Converter Adapter

    Original price was: ₨ 300.Current price is: ₨ 270.
    The USB to RS485 Converter Adapter module support WIN7 XP Vista Linux Mac OS provides an easy-to-use RS485 interface by means of a Virtual Com Port on the user’s system. There are no command structures, whatever is sent to the Virtual Comm Port is automatically converted to RS485 and vice versa. The module is completely self-powered from the USB bus. Controlling / Communicating with RS-485 devices from your PC has never been easier! This device is plug-and-play. It shows up as a serial/com port and is accessible from applications or hyper-terminal.
    Add to wishlist
    Add to cart
    Quick view